845-292-6400

518-438-6433

135 Chestnut St, New Paltz NY

845-256-6400

Wholesale Distributors where "Serving you is our Only Business" Thanks for dropping by.

Tell A Friend

Recommend this Site

Yaun Company FAQ's

Browse by Category
	Technical Questions (26) Technical Questions about Our Products
	Design and Application Questions (1) Design and Application Questions about Products that we Sell

Home

Search Knowledgebase

Jump to Category

Technical Questions	[ All FAQ In This Category ]
Plumbing	[ All FAQ In This Category ]
Can a Viega Pro Press Tool be used to Press a Nibco Press Fitting??
Domestic Water Systems	[ All FAQ In This Category ]
What information do I need to fully test my water in my house for water quality
Hydronic - Radiant Heating	[ All FAQ In This Category ]
I have a job with Cast Iron Radiation can I add a condensing boiler????
What is Pex??
Can a 3-Speed Grundfos Pump be used with a Tek-Mar variable speed pump controller
Can a Viega Pro Press Tool be used to Press a Nibco Press Fitting??
Does Cryo-tek reduce the efficiency of a heating system?
What would be a good mixture for anti-freeze protection in the New Jersey, New York region?
Why is there a white slime forming in my pex radiant heat tubing?
Biasi Boilers	[ All FAQ In This Category ]
Beckett Burner installs into the Combustion Chamber is this Correct
Controls & Wiring	[ All FAQ In This Category ]
I have a newly purchased Honeywell R7184 Oil Burner Primary Control and can't get it to run. What Can the problem be??
What Should I do to recover my Boiler that has been submerged under water
I have a control that has uses a thermistor to sense temperature. How do I tell if the sensor is good??
HVAC	[ All FAQ In This Category ]
Do the threads on my Miller - Nordyne Quick Connect linesets require Lubrication??
Do I need to install a liquid line drier and sight glass when installing a minisplit system???
Register and Duct Sizing and Design	[ All FAQ In This Category ]
How do I select Filter Grills??
How do I size a bath fan correctly?? I'm tired of using confusing rules of thumb
Chimneys, Flues, and Exhaust	[ All FAQ In This Category ]
I notice that your Magic Heaters have the crimp opposite of what I would expect?? Why??
For Magic Heaters, How does this work whenI clean the chimney/flue. Does it actually burn the creosote from slow/low fires. Usually clean chimney only 1x year since wood air tight (napoleon) is our only heat source. Mostly burned at med.high to high all winter (8 months) thanks in advance
Controls and Wiring	[ All FAQ In This Category ]
My electric programmable thermostat won't bring on the blower in heating mode. You can bring the blower on by switching the sub-base to "on" but on a call for heat the blower won't operate. What can be the problem??
I have a furnace or air conditioner that has been under water. What should I do to get it running.
I just installed a Ruud Gas Furnace and it doesn't want to fire? What should I be looking for??
i have a rheem high efficient furnace that is 8 years old, my problem is excessive moisture in the upper cabinet area. what could be the possible cause of this? At first i thought it was the really cold air it was bringing in the intake but it since has warmed up and it still seems to have the moisture. is there a seal around the exhaust blower unit that could be putting combustion air back into the cabinet? Thanks.
A/C and Refrigerants	[ All FAQ In This Category ]
What is the Real Difference between R22 and R410A Refrigerants
On an A/C job that I am doing I found that I have put in an oversized liquid line. I was rushing and got my line sets reversed. Can I use the oversized liquid line for the smaller unit??
Electrical Distri bution	[ All FAQ In This Category ]
What size wire should I use for a job??
Design and Application Questions	[ All FAQ In This Category ]
Job Design	[ All FAQ In This Category ]
How do I size a bath fan correctly?? I'm tired of using confusing rules of thumb

This campaign has been closed from voting

Announcements
No Announcement